Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
We've discovered this great article about How to Install a Bathtub Yourself down the page on the internet and decided it made perfect sense to discuss it with you on this page.
Installing a tub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard task. If the old bathtub is readily accessible, the project can move quickly; if you have to open a wall to eliminate the old tub as well as position the new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the new one. Ensure you have qualified yourself for the job and also fit trying it. As opposed to employing a specialist to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your washroom if you have actually currently purchased a new bathtub and also don't need to change the setup of your previous water system pipes.
Your tools and product list ought to comprise the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the restricted accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new taps, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Secure the tap in place with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap ports. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait until the bath tub has actually been used at the very least once as this will resolve it into its last setting.
Preparing for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to prevent pressure on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can fracture rather early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that write-up on A Step-by-Step Guide to Installing a Bathtub from an associate on a different web property. In case you enjoyed reading our blog entry if you please do not forget to pass it around. Thanks a lot for taking the time to read it.
Schedule Your Job Now
Report this page